Used Plastic Machinery

Complete System – Installed and Operational Voltage: 460V PFV200/15 Agglomerator Knife Mill Model PSP 400×500 Year(s) : 2004 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

20′ CDS Spray Tank Model CST 12-20, 12″ x 12″ Cross Section 7.5hp Water Recirculation Pump Heat Exchanger Wate Year(s) : 2000 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

4.5″ Sterling Single Screw Extruder 200 HP (motor was purchased rebuilt 1 year ago) New VFD Drive (purchased n Location : AMERICA North (USA-Canada-Mexico)

Price : On request

6′ Nrm Reconditioned Extruder 30:1 L/D VENTED 43″ centerline height New gernox seals Complete with gearbox Location : AMERICA North (USA-Canada-Mexico)

Price : On request

2 1/2” Killon Davis Rubber Extruder with power Roll Feed. 12.8 to1 L.D. 3 Barrel Zones two Die Zones Air Coole Location : AMERICA North (USA-Canada-Mexico)

Price : On request

1 1/2″ Gloucester 24:1 Water Cooled Extruder 24:1 Water Cooled 4 Barrel Zones 1 Gate 3 Die Zones Barber Colema Location : AMERICA North (USA-Canada-Mexico)

Price : On request

1.5″ Gloucester 24:1 N-Vented Extruder water cooled with dryer Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Rebuilt- approximately 43″ centerline height Gearbox having new bearing (less thrust) and seals with cooling u Location : AMERICA North (USA-Canada-Mexico)

Price : On request

24:1 Air Cooled 40 H.P. D.C. Motor and Drive. 4 Barrel Zones 4 Die Zones 2 Screws. Hopper Dryer with Loader Location : AMERICA North (USA-Canada-Mexico)

Price : On request

440 Cu Ft Drying Hopper Capacity 1500 lbs. Location : AMERICA North (USA-Canada-Mexico)

Price : On request

18″ x 65″ 3-Roll Stack 8″ x 65″ Pull Roll Assembly Location : AMERICA North (USA-Canada-Mexico)

Price : On request

6″ NRM Plastics Extruder Rebuilt approximately 43″ centerline height gearbox having new bearing (less thrust) Location : AMERICA North (USA-Canada-Mexico)

Price : On request

We have two 1″ Akron Extruders – being rebuilt – Photos shown during process Rebuilt Gearbox new bearings and Location : AMERICA North (USA-Canada-Mexico)

Price : On request

6″ Sterling / Davis Standard extruder 30 to 1 L/D ratio – air cooled barrel 400 HP DC motor Year(s) : 2011 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

3 1/2” Extruder 32:1 L.D. Gear Box Ratio: 15.12.1 100 H.P. D.C. Motor and Drive. Vented and Plugged. Water Coo Year(s) : 1988 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Total Rebuild 3/4” 24:1 Extruder A.Rebuilt Gearbox. B. New Belts. C. New Barrel. D. New Heater Bands & Blowers Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Reconditioned 1” 24:1 Merit-Davis Post Extruder 3 Barrel Zones 1 Adapter 2 Die- Air Cooled. Melt Temp. Melt P Location : AMERICA North (USA-Canada-Mexico)

Price : On request

31/2” 30:1 100 Hp DC Screen changer Gear pump Was set up to run cast film Water Cooled Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Rebuilt 2 1/2” Rebuilt Gear Box. Gear Box Ratio: 17.1 New Barrel. Used General Purpose Screw Good Condition. Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Reconditioned 3/4” Extruder 24:1 Air Cooled New RKC Dual Display Controllers New Relays 3 Barrel Zones 2 Die Z Year(s) : 1996 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Reconditioned 1 1/4” 24:1 Extruder.Vented Barrel with Plug. General Purpose Screw used Good Condition. Air Coo Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Xaloy Water Ring Pelletizer with Die Head, WRP12 Spin Dryer Control Panel 30 Hole, 1/8″ (3mm) Diameter Die Hea Location : AMERICA North (USA-Canada-Mexico)

Price : On request

With Heavy Duty 5/8″ thick screen with 44 holes 1 spare set of “new” Bed Knives 63″ wide x 80″ long ram dimens Year(s) : 2017 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Vecoplan RG52/150 SPK FF (Film & Fiber) Shredder W/Conveyors & Box Dumper Model RG 52-150SPK-FF heavy-duty, si Year(s) : 2003 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Brand: BANDERA Diameter: 120 mm, 25 L/D Screw length: 3 m Extruder electrical control panel Location : EUROPE (Western and Northern)

Price : On request